DOLPHIN SM SERIES

The Dolphin SM Series robot operates independently of the main filtration system, using its own electric motor to maintain constant suction power without overloading the pool pump. On sloped floors and liner walls, the toothed-track traction offers clear advantages:

• Continuous grip on slippery surfaces without slipping on sloped transitions.
• Active front brushing with a double-speed forward rotation to dislodge biofilm from liner and concrete surfaces before vacuuming the debris.
• Fully independent of the skimmer, preventing leaves or grit from clogging the pool filter's pre-filter.
• Programmed autonomous cycle that ends with automatic shutoff after completing 2 hours of operation.

This configuration protects the installation's mechanics and significantly reduces the need for sand filter backwashing.

Maintaining the filter basket in Dolphin SM Series equipment requires only removing the compartment from the top and quickly rinsing it with a garden hose without pressure. To preserve the nominal suction flow throughout the 2026 season, follow these steps after each cycle:

• Press the release latch on the upper housing to remove the modular basket.
• Open the lower hatch to empty bulky debris directly into a container.
• Rinse the four ultra-fine panels with clean water until all dust particles and plant debris are removed.
• Refit the filter block, making sure the safety clip is closed before storing the equipment.

Completing this procedure prevents premature clogging of the internal pump motor and extends the equipment's service life.

A Dolphin Serie SM pool cleaner is designed to remove debris that has settled on the bottom, so the water's chemical balance must be adjusted before starting automatic cleaning. If there are colloidal suspensions or green algae blooms, the filter will trap dirt too quickly, requiring frequent stops. We recommend treating the water beforehand by dosing Piscimar's ULTRA CLEAR clarifier to clump microscopic particles at the bottom of the pool. Once the dirt has settled with the filtration off overnight, put the robot in with its clean panel filter basket to collect the sediment in a single continuous cycle without clouding the pool again.

Dolphin Serie SM pool cleaners are compatible with in-ground and above-ground pools with rigid walls, up to a maximum length of 12 meters. Their high-friction track-drive system works effectively on ceramic tile, fiberglass, polyester, painted concrete, and reinforced liner surfaces. The smart scanning algorithm for residential pools up to 10 to 12 meters, with a 2-hour closed cycle, calculates the cleaning path to adapt to rectangular, oval, or free-form configurations, handling gently sloping floors or compound slopes without manual intervention.

The Dolphin SM Series robot uses an external power supply that converts household 230 V current to a safe DC voltage below 30 V before the power reaches the floating cable. This eliminates any risk of electric shock in the water during operation. In addition, the transformer features IP54 insulation and automatic thermal shutdown in the event of power surges. If you want additional perimeter monitoring while the automatic equipment runs its cleaning cycles, you can install an Aqualarm pool alarm to instantly detect accidental falls into the water by children or pets.

A Dolphin SM Series uses between 120 and 180 watts per hour during its usual 2-hour cycle. This amounts to a total energy consumption of approximately 0.24 to 0.36 kWh per complete pool cleaning. Compared with a conventional hydraulic system connected to a traditional 0.75 HP filtration pump (which uses about 750 watts per hour of operation), using the Dolphin autonomous robot reduces electricity consumption by more than 70% during each maintenance session.

Properly winterizing the Dolphin SM Series robot requires completely drying the internal components and protecting the plastic parts from direct frost. At the end of the swimming season, carry out the following maintenance steps:

• Wash the filter panels thoroughly and let them dry in the shade to prevent mold from forming.
• Rinse the equipment’s chassis with fresh water to remove any chlorine residue or salt buildup on the bearings.
• Coil the floating cable without forcing any bends, following the cable’s natural bend radius.
• Store the robot resting on its tracks or on its transport stand in a well-ventilated place at temperatures between 5 °C and 35 °C.

Keeping the transformer away from ambient moisture ensures a flawless start when the system is reactivated in spring.