Cantabric Lateral Filter, Ø 600. Astralpool. 15783.
Cantabric Lateral Filter, Ø 600. Astralpool. 15783. is backordered and will ship as soon as it is back in stock.
Transit time 3 - 5 days
Description
Description
Filter injected in technical plastics. Ivory color. Union of the upper and lower part of the filter by thermal welding. Equipped with pressure gauge, manual water and air purges. Side selector valve included. Max speed filtration of 50 m³/h/m². Maximum working pressure: 2.5 kg/cm².
Cantabric C/Valve filters are equipped with:
- Ø 2" sand drain plug on Ø 750 mm models.
- Sand drain plug Ø 1½" in the Ø 400 mm, Ø 500 and Ø 600 mm models.
To obtain maximum performance from these filters, they must be filled with siliceous sand with a grain size of 0.5 to 0.7 mm.
Technical characteristics
| Code | Ø mm | Connection (inches) | Filtration surface | Filtration speed (m²) | Flow rate (m³/h) | Service pressure (bar) | Sand load (0.4 - 0.8 mm) (Kg) | Net weight (Kg) |
| 22398 | 400 | 1½ | 0,126 | 50 | 6 | 2,5 | 60 | 7 |
| 15782 | 500 | 1½ | 0,196 | 50 | 9 | 2,5 | 100 | 12 |
| 15783 | 600 | 1½ | 0,283 | 50 | 14 | 2,5 | 150 | 14 |
| 15784 | 750 | 2 | 0,442 | 50 | 21 | 2,5 | 300 | 24 |
Installation
The Cantabric C/Valve filter should be installed as close as possible to the pool and preferably at a level of 0.50 meters. below the surface of the pool water. Always ensure that there is a drain for the room where the filter is located. For a correct installation of the filter you must proceed with the installation as follows:
- Make sure that the surface where the filter is installed is horizontal and completely clean.
- Install the filter in its final location.
- In the case of a filter with a side valve, install the selector valve on the filter, ensuring that the gaskets between the valve and the filter are correctly positioned.
- Make the three relevant connections of the selector valve: pipe from the pump to the valve to the pool return. Each of the three outlets is identified on the valve
- Assemble the pressure gauge, gasket, pressure gauge and air purge plug.
- Do not tighten the pressure gauge tee with any tool as your hands are sufficient.
Important: If you install the filter in a premises, a correctly sized drain must be installed to evacuate the maximum inflow from the pool in order to avoid the risk of flooding in the premises itself or adjacent premises. If this obligation is not met, the filter manufacturer will not be responsible for possible damage to third parties caused by any incident in the filter itself.
 |
Operation
The selector valve has a lever with 6 positions, thus allowing you to select any of the operations for correct filter operation.
Important: Always change the position of the selector valve with the pump stopped.
Start-up
Once the sand filter has been loaded, it is necessary to wash it. Proceed as follows:
- Open the air bleed plug to bleed the air.
- Place the selector valve in the "Wash" position
- Open the valves that control the pool suction pipes and connect the pump for approx. 4 minutes. pump and place the selector valve handle in the "Filtration" position.
- Close the air vent plug when the water comes out.
- Once these operations have been carried out, you will have the filter ready to begin the water filtration cycles in the pool.
Important: Carry out the position changes of the selector valve handle with the pump disconnected.
MEASUREMENTS:
